This step by step woodworking project is about free 14×14 lean to shed roof plans. This is PART 2 of the square storage lean to shed project where I show you how to frame the roof and how to build the front door and window. The lean to roof with a 3:12 pitch is the ideal choice if you want to build it near the property line. Moreover, the front and side doors are ideal for using this shed for storage or as a workshop. See my other DIY projects HERE.
We recommend you to invest in the best materials you could afford. Therefore, you should buy weather-resistant lumber, such as pine or cedar. Always take accurate measurements before adjusting the size of the components at the proper size. Drill pilot holes trough the components before inserting the wood screws, to prevent the wood from splitting. See all my Premium Plans HERE.
Made from this plan
Building a Lean to Roof for a 14×14 Shed
Building-a-14×14-lean-to-shed
Materials
- I – 11 pieces of T1-11 siding – 48″x96″ long, 3 pieces – 24″x96″ long, 1 piece – 48″x7″ long, 1 piece – 24″x48″ long, 2 pieces – 48″x50″ long, 2 pieces – 48″x38″ long, 2 pieces – 24″x26″ long, 2 pieces – 48″x20″ long SIDING
- J – 8 pieces of 2×10 lumber – 16 ft long RAFTERS
- K – 13 pieces of 1×4 lumber – 108″ long, 13 pieces – 84″ long PURLINS
- L – 12 pieces of metal roof sheets – 3’x10′ ROOFING
- M – 2 pieces of 2×4 lumber – 80″ long, 1 piece – 39″ long JAMBS
- N – 2 pieces of 2×4 lumber – 73″ long, 2 pieces – 32″ long, 1 piece – 25″ long SIDE DOOR
- P – 2 pieces of 2×4 lumber – 87 1/2″ long, 1 piece – 103″ long JAMBS
- P – 2 pieces of 2×4 lumber – 80 1/2″ long, 2 piece – 48″ long, 1 piece – 41″ long 2xDOOR
- 8 pieces of 2×10 lumber – 16 ft
- 13 pieces of 1×4 lumber – 10 ft
- 15 pieces of 1×4 lumber – 8 ft
- 15 pieces of 2×4 lumber – 8 ft
- 1 piece of 2×10 lumber – 10 ft
- 2 pieces of 1×6 lumber – 16 ft
- 18 pieces of T1-11 siding – 4’x8′
- 12 pieces of metal roof sheets – 3’x10′
- 1 piece of PVC window – 36″x36″
- 2 kits of hinges & latch
- 250 pieces of 2 1/2″ screws
- 500 pieces of 3 1/2″ screws
- 500 pieces of 1 5/8″ screws
- 500 pieces of 6d nails
- 16 pieces of rafter ties
- 1 box of 1 1/2″ structural screws
- wood filler , wood glue, stain/paint
Tools
- Safety gloves, glasses
- Miter saw, jigsaw
- Chalk line, tape measure, spirit level, carpentry pencil
- Drill machinery and drill bits
Time
- One week
Step 5: Building the lean to shed roof
Rafters-for-the-lean-to-shed
Firstly, build the rafters for the lean to roof using 2×10 lumber (read the local codes for best choice). Mark the cut lines on the slats and get the job done with a circular saw. The birdsmouth cuts are needed so you can fit the rafters into place tightly. You have everything you need to make the cuts, in the diagram.
If you change the roof pitch, you need to make adjustments to the birdsmouth cuts.
Fitting-the-rafters-to-the-garden-shed
Next, fit the rafters every 24″ on center and align the edges with attention. Use rafter ties and 1 1/2″ structural screws to lock the rafters to the wall frames. Align the rafters with attention before setting them to the top plates with ties and screws.
Step 6: Attaching the siding sheets
Back-wall-siding-sheets
Use 5/8″ T1-11 siding for the back of the shed. Make the cuts to the sheets and then align them into place. Use 6-8d nails, every 8″ along the framing. Also, I recommend you to leave no gaps between the panels.
Front-siding-sheets—14×14-shed
Attach the siding sheets to the opposite wall of the shed. Leave no gaps between the sheets and use the same procedure shown above. In addition, use a circular saw to make the cuts around the window and door openings.
Side-panels-for-lean-to
Fit the T1-11 siding panels to the sides of the storage shed. On one side of the garden shed use a saw to make the cuts around the double door opening.
Step 7: Fitting the roofing
Fitting-the-purlins-to-the-large-shed
I recommend you to use 1×4 lumber for the purlins. Set the boards to the top of the shed, as shown in the diagram. Use 2 1/2″ screws to lock the purlins to the rafters. You can adjust the size of the 12″ side overhangs to suit your needs. Fit the purlins every 16″ on center.
Fitting-the-roof-trims
In addition, you can add 1×6 boards to the front and back of the roof, to hide the ends of the rafters. Use 6d nails or screws to lock these trims to the rafters,
Fitting-the-metal-sheet-roofing
I have designed this shed with metal sheets roofing. Therefore, you need to set the metal sheets to the roof structure and lock them to the purlins with the appropriate screws.
Alternatively, you can use 3/4″ plywood instead of the purlins and then install asphalt shingles. It is up to you what materials you use.
Step 8: Building the front shed door
Fitting-the-front-window
Fit the 36″x39″ PVC shed window into place and then attach the 1×4 decorative ends to enhance the look of the project.
Door-jambs—front-shed-wall
Fit 2×4 jambs around the door opening. Align the boards with attention and then lock them into place tightly with 2 1/2″ screws.
Door-frame-for-shed
Next, build the door frame for the shed. Cut all components for the frame from 2×4 lumber. Drill pocket holes at both ends of the vertical and middle boards. Lay the slats on a level surface, align the edges flush and make sure the corners are square. Insert 2 1/2″ screws to assemble the door frame together tightly.
Assembling-the-32-inch-shed-door
Continue the project by attaching the T1-11 siding that you have cut out in the previous steps and lay them over the door frames. Use 1 5/8″ screws to secure the panels to the frames tightly. Make sure the edges are flush.
Fitting-the-door-to-the-front-of-the-large-shed
Fit the door to the front of the garden shed. Align the edges with attention and lock them to the jambs with hinges. Attach a latch to lock the doors together tightly.
Double-door-jambs-for-garden-shed
Fit the 2×4 jambs around the double door opening.
Assembling the door frame
The next step is to assemble the frames for the side double doors. Use 2×4 lumber for the components and make sure the corners are square and align the edges flush. Insert 2 1/2″ screws and pocket holes to assemble the frame.
Assembling the door
Attach the T1-11 siding sheets to the frames.
Fitting-the-double-doors-to-the-side-of-the-shed
Fit the double doors to the side of the lean to shed. Align the edges and set the hinges to lock the doors to the jambs. In addition, install the latch so you can keep the doors locked together tightly.
Step 9: Finishing touches
How-to-build-a-14×14-lean-to-shed
Also, you need to take care of the finishing touches. Therefore, fill the holes with wood putty and then smooth the surface with sandpaper. Apply a few coats of paint or stain over the components to enhance the look of the shed and to protect the components from decay.
14×14-lean-to-shed-plans—full-dimensions
I have designed this large 14×14 lean to shed so you can store all your garden tools and organize the rest of your items. Check out PART 1 of the project for free shed frame plans. See all my SHED PLANS, as well, as I have lots of designs that come in many sizes. You can see in the diagram the overall dimensions of the shed, so you can decide if this is what you are looking for.
Thank you for reading our project about free 14×14 lean to shed roof plans and I recommend you to check out the rest of the projects. Don’t forget to LIKE and SHARE our projects with your friends, by using the social media widgets. SUBSCRIBE to be the first that gets our latest projects.
<< Previous | Next >>
 |
 |
EXPLORE MORE IDEAS:
 |
 |
 |
 |
 |