5×10 Shed – Lean to Roof Plans

This step by step woodworking project is about free 5×10 lean to shed roof plans. This is PART 2 of the small storage lean to shed project where I show you how to frame the roof and how to build the front door. The lean to roof is the ideal choice if you want to build it near the property line. Moreover, the 32″ wide front door will help you have an easy access inside the shed with large objects. See my other DIY projects HERE.

We recommend you to invest in the best materials you could afford. Therefore, you should buy weather-resistant lumber, such as pine or cedar. Always take accurate measurements before adjusting the size of the components at the proper size. Drill pilot holes trough the components before inserting the wood screws, to prevent the wood from splitting. See all my Premium Plans HERE.

Made from this plan

5×10 Lean to Shed Roof Plans

Building-a-5×10-lean-to-shed

Materials

H – 9 pieces of 2×4 lumber – 84″ long RAFTER
I – 2 pieces of T1-11 siding – 48″x104 1/4″ long, 2 pieces – 24″x104 1/4″ long, 2 pieces of 48″x107 3/4″ long, 2 pieces – 48″x83 3/4″ long, 2 pieces – 24″x83 3/4″ long, 2 pieces – 24″x96″ long SIDING
J – 6 pieces of 1×4 lumber – 136″ long PURLINS
K – 2 pieces of 1×6 lumber – 136″ long ROOF TRIMS
L – 4 pieces of metal roof sheets – 3’x8′ ROOFING
M – 2 pieces of 2×4 lumber – 79″ long, 1 piece – 39″ long JAMBS
N – 2 pieces of 2×4 lumber – 72″ long, 2 pieces – 32″ long, 1 piece – 25″ long, 1 piece of T1-11 siding – 32″x79″ long DOOR

15 pieces of 2×4 lumber – 8 ft
2 pieces of 1×6 lumber – 12 ft
6 pieces of 1×4 lumber – 12 ft
5 pieces of T1-11 siding – 4’x10′
4 pieces of T1-11 siding – 4’x8′
4 pieces of metal roof sheets – 3’x8′
1 kit of hinges & latch
250 pieces of 2 1/2″ screws
500 pieces of 3 1/2″ screws
500 pieces of 1 5/8″ screws
500 pieces of 6d nails
1 box of 1 1/2″ structural screws
wood filler , wood glue, stain/paint

Tools

Safety gloves, glasses
Miter saw, jigsaw
Chalk line, tape measure, spirit level, carpentry pencil
Drill machinery and drill bits

Time

One week

Step 5: Building the lean to shed roof

Rafters-for-5×10-shed

Firstly, build the rafters for the lean to roof using 2×4 lumber. Mark the cut lines on the slats and get the job done with a circular saw. The birdsmouth cuts are needed so you can fit the rafters into place tightly. You have everything you need to make the cuts, in the diagram.

Fitting-the-rafters

Next, fit the rafters every 16″ on center and align the edges with attention. Use rafter ties and 1 1/2″ structural screws to lock the rafters into place tightly.

Step 6: Attaching the siding sheets

Tall-side-wall-siding-sheets

Use T1-11 siding for the side walls for the shed. Make the cuts to the sheets and then align them into place. Use 6-8d nails, every 8″ along the framing.

Short-side-wall-siding-sheets

Attach the siding sheets to the opposite side of the shed. Leave no gaps between the sheets and use the same procedure shown above.

Front-and-back-wall-siding-sheets

Nevertheless, you need to make the cuts around the door opening so you can fit the door. Use a circular saw to get the job done.

Step 7: Fitting the roofing

Fitting-the-purlins—lean-to-shed

I recommend you to use 1×4 lumber for the purlins. Set the boards to the top of the shed, as shown in the diagram. Use 2 1/2″ screws to lock the purlins to the rafters. You can adjust the size of the side overhangs to suit your needs.

Fitting-the-roof-rafters

In addition, you can add 1×6 boards to the sides of the roof, to hide the ends of the rafters. Use 6d nails or screws to lock these trims to the rafters,

Fitting-the-roofing-sheets

I have designed this shed with metal sheets roofing. Therefore, you need to set the metal sheets to the roof structure and lock them to the purlins with the appropriate screws.

Step 8: Building the front shed door

Fitting-the-door-jambs

Fit 2×4 jambs around the door opening. Align the boards with attention and then lock them into place tightly with 2 1/2″ screws.

Door-frame

Next, build the door frame for the shed. Cut all components for the frame from 2×4 lumber. Drill pocket holes at both ends of the vertical and middle boards. Lay the slats on a level surface, align the edges flush and make sure the corners are square. Insert 2 1/2″ screws to assemble the door frame together tightly.

Assembling-the-shed-door

Continue the project by attaching the T1-11 siding that you have cut out in the previous steps and lay them over the door frames. Use 1 5/8″ screws to secure the panels to the frames tightly. Make sure the edges are flush.

Fitting-the-shed-door

Fit the door to the front of the garden shed. Align the edges with attention and lock them to the jambs with hinges. Attach a latch to lock the doors together tightly.

Step 9: Finishing touches

How-to-build-a-5×10-lean-to-shed

Last but not least, you need to take care of the finishing touches. Therefore, fill the holes with wood putty and then smooth the surface with sandpaper. Apply a few coats of paint or stain over the components to enhance the look of the shed and to protect the components from decay.

5×10-Lean-to-Shed-Plans—dimensions

I have designed this small 5×10 lean to shed so you can store all your garden tools and organize the rest of your items (sports equipment and so on). Check out PART 1 of the project for free shed frame plans. See all my SHED PLANS, as well, as I have lots of designs that come in many sizes. You can see in the diagram the overall dimensions of the shed, so you can decide if this is what you are looking for.

Thank you for reading our project about free 5×10 lean to shed roof plans and I recommend you to check out the rest of the projects. Don’t forget to LIKE and SHARE our projects with your friends, by using the social media widgets. SUBSCRIBE to be the first that gets our latest projects.

<< Previous | Next >>