10×16 Lean to Shed – Free DIY Plans

This step by step woodworking project is about free 10×16 lean to shed roof plans. This is PART 2 of the square storage lean to shed project where I show you how to frame the roof and how to build the front double doors. The lean to roof with a 3:12 pitch is the ideal choice if you want to build it near the property line. Moreover, the front and side doors are ideal for using this shed for storage or as a workshop. See my other DIY projects HERE.

We recommend you to invest in the best materials you could afford. Therefore, you should buy weather-resistant lumber, such as pine or cedar. Always take accurate measurements before adjusting the size of the components at the proper size. Drill pilot holes trough the components before inserting the wood screws, to prevent the wood from splitting. See all my Premium Plans HERE.

Made from this plan

Building a Lean to Roof for a 10×16 Shed

Building-the-10×16-lean-to-shed

Materials

H – 10 pieces of T1-11 siding – 48″x84″ long, 4 pieces – 48″x24″ long, 2 pieces – 24″x84″ long, 2 pieces – 48″x8 1/2″ long, 2 pieces – 48″x29 1/2″ long, 2 pieces – 48″x19 1/2″ long, 2 pieces – 24″x9 3/4″ long SIDING
I – 9 pieces of 2×6 lumber – 12 ft long RAFTERS
J – 20 pieces of 1×4 lumber – 108″ long PURLINS
K – 4 pieces of 1×8 lumber – 108′ long, 2 pieces of 1×4 lumber – 32″ long, 2 pieces – 39″ long TRIMS
L – 12 pieces of metal roofing 3’x8′ ROOFING
M – 2 pieces of 2×4 lumber – 75 1/2″ long, 1 piece – 103″ long JAMBS
N – 2 pieces of 2×4 lumber – 68 1/2″ long, 2 piece – 48″ long, 1 piece – 41″ long 2xDOOR

9 pieces of 2×6 lumber – 12 ft
22 pieces of 1×4 lumber – 10 ft
4 pieces of 1×8 lumber – 10 ft
9 pieces of 2×4 lumber – 8 ft
1 piece of 2×4 lumber – 10 ft
14 pieces of T1-11 siding – 4’x8′
12 pieces of metal roof sheets – 3’x8′
1 piece of PVC window – 32″x32″
2 kits of hinges & latch
250 pieces of 2 1/2″ screws
500 pieces of 3 1/2″ screws
500 pieces of 1 5/8″ screws
500 pieces of 6d nails
16 pieces of rafter ties
1 box of 1 1/2″ structural screws
wood filler , wood glue, stain/paint

Tools

Safety gloves, glasses
Miter saw, jigsaw
Chalk line, tape measure, spirit level, carpentry pencil
Drill machinery and drill bits

Time

One week

Step 5: Building the lean to shed roof

Rafters-for-10×16-lean-to

Firstly, build the rafters for the lean to roof using 2×6 lumber (read the local codes for best choice). Mark the cut lines on the slats and get the job done with a circular saw. The birdsmouth cuts are needed so you can fit the rafters into place tightly. You have everything you need to make the cuts, in the diagram.

If you change the roof pitch, you need to make adjustments to the birdsmouth cuts.

Fitting-the-rafters-to-the-10×16-shed

Next, fit the rafters every 24″ on center and align the edges with attention. Use rafter ties and 1 1/2″ structural screws to lock the rafters to the wall frames. Align the rafters with attention before setting them to the top plates with ties and screws.

Step 6: Attaching the siding sheets

Back-wall-siding-sheets-for-lean-to-shed

Use 5/8″ T1-11 siding for the back of the shed. Make the cuts to the sheets and then align them into place. Use 6-8d nails, every 8″ along the framing. Also, I recommend you to leave no gaps between the panels.

Front-wall-siding-for-shed

Attach the siding sheets to the opposite wall of the shed. Leave no gaps between the sheets and use the same procedure shown above. In addition, use a circular saw to make the cuts around the double door opening. Align the edges flush and insert 6d nails to lock them into place, every 8″ along the framing.

Side-supports—roof

Use 2×4 lumber for the side lean to supports. Make the angle cuts to one end of the supports, drill pocket holes and insert 2 1/2″ screws to lock them to the rafters and side top plates.

Side-siding-sheets

Fit the T1-11 siding panels to the sides of the storage shed. Use a saw to make the cuts around the window openings.

Step 7: Fitting the roofing

Fitting-the-shed-roof-purlins

I recommend you to use 1×4 lumber for the purlins. Set the boards to the top of the shed, as shown in the diagram. Use 2 1/2″ screws to lock the purlins to the rafters. You can adjust the size of the 12″ side overhangs to suit your needs. Fit the purlins every 16″ on center.

Roof-trims

In addition, you can add 1×8 boards to the front and back of the roof, to hide the ends of the rafters. Use 6d nails or screws to lock these trims to the rafters,

Fitting-the-roof-sheets

I have designed this shed with metal sheets roofing. Therefore, you need to set the metal sheets to the roof structure and lock them to the purlins with the appropriate screws.

Alternatively, you can use 3/4″ plywood instead of the purlins and then install asphalt shingles. It is up to you what materials you use.

Step 8: Building the front shed door

Fitting-the-window

Fit the 32″x32″ PVC shed window into place and then attach the 1×4 decorative ends to enhance the look of the project.

Fitting-the-door-jambs

Fit 2×4 jambs around the door opening. Align the boards with attention and then lock them into place tightly with 2 1/2″ screws.

Assembling-the-shed-door-frame

Next, build the door frame for the shed. Cut all components for the frame from 2×4 lumber. Drill pocket holes at both ends of the vertical and middle boards. Lay the slats on a level surface, align the edges flush and make sure the corners are square. Insert 2 1/2″ screws to assemble the door frame together tightly.

Assembling-the-shed-door

Continue the project by attaching the T1-11 siding that you have cut out in the previous steps and lay them over the door frames. Use 1 5/8″ screws to secure the panels to the frames tightly. Make sure the edges are flush.

Fitting-the-double-doors

Fit the door to the front of the garden shed. Align the edges with attention and lock them to the jambs with hinges. Attach a latch to lock the doors together tightly.

Step 9: Finishing touches

10×16-Lean-to-shed-Plans-Free

Also, you need to take care of the finishing touches. Therefore, fill the holes with wood putty and then smooth the surface with sandpaper. Apply a few coats of paint or stain over the components to enhance the look of the shed and to protect the components from decay.

10×16-Lean-to-shed-Plans-dimensions

I have designed this large 10×16 lean to shed so you can store all your garden tools and organize the rest of your items. This is the ideal project for you, in case you need a garden shed with large double doors, so you can store large items. Check out PART 1 of the project for free shed frame plans. See all my SHED PLANS, as well, as I have lots of designs that come in many sizes. You can see in the diagram the overall dimensions of the shed, so you can decide if this is what you are looking for.

Thank you for reading our project about free 10×16 lean to shed roof plans and I recommend you to check out the rest of the projects. Don’t forget to LIKE and SHARE our projects with your friends, by using the social media widgets. SUBSCRIBE to be the first that gets our latest projects.

<< Previous | Next >>