This step by step woodworking project is about 4×12 gable shed roof plans. This is the PART 2 of the 4×12 garden shed project, where I show you how to build the gable roof for the shed. Building the roof for the shed is really easy if you follow my tips and diagrams with attention. Read the local codes before starting the project, so you comply with the requirements. See my other DIY projects HERE.
We recommend you to invest in the best materials you could afford. Therefore, you should buy weather-resistant lumber, such as pine or cedar. Always take accurate measurements before adjusting the size of the components at the proper size. Drill pilot holes trough the components before inserting the wood screws, to prevent the wood from splitting. See all my Premium Plans HERE.
Made from this plan
4×12 Gable Shed Roof Plans
Building a 4×12 shed
Materials
- D – 2 pieces of 5/8″ T1-11 siding – 15 3/4″x48″ long SIDING
- E – 2 pieces of 2×4 lumber – 9 3/4″ long, 1 pieces of 2×6 lumber – 144″ long RIDGE
- F – 14 pieces of 2×4 lumber – 35 1/4″ long RAFTERS
- G – 4 pieces of 2×4 lumber – 35 1/4″ long, 10 pieces – 2 1/2″ long OVENHANG
- H – 2 pieces of 3/4″ plywood – 35 1/4″x96″ long, 2 pieces – 35 1/4″x96″ long, 4 pieces – 6″35 1/4″ long ROOF
- I – 2 pieces of 1×4 lumber – 156″ long TRIMS
- J – 120 sq ft of tar paper, 120 sq ft of asphalt shingles ROOFING
- 13 pieces of 2×4 lumber – 6′
- 1 piece of 2×6 lumber – 12′
- 2 pieces of 1×4 lumber – 14′
- 2 pieces of 2×6 lumber – 6′
- 3 pieces of 3/4″ plywood – 48″x96″
- 1 piece of T1-11 5/8″ siding – 4’x8′
- 120 sq ft of tar paper, 120 sq ft of asphalt shingles
- 2 1/2″ screws, 3 1/2″ screws, 1 5/8″ screws
- 4d nails, 6d nails
- rafter ties
- shed hinges
- wood filler , wood glue, stain/paint
Tools
- Safety gloves, glasses
- Miter saw, jigsaw
- Chalk line, tape measure, spirit level, carpentry pencil
- Drill machinery and drill bits
Time
- One week
4×12 Gable Shed Roof Plans
Fitting the ridge beam
Use 2×4 lumber for the supports. Drill pocket holes at both ends of the supports and lock them to the center of the plates with 2 ½” screws. Fit the ridge beam and secure it to the supports with 2 ½” screws. Use a spirit level to check if the beam is horizontal.
Building the rafters
Use 2×4 lumber for the rafters. Mark the cut lines on the beams and then get the job done with a circular saw. Smooth the edges with sandpaper.
Fitting the rafters
Fit the rafters to the top of the shed. Place the rafters every 24″ on center, equally spaced, as shown in the diagram. Drill pilot holes and insert 3 1/2″ screws to lock the rafters into place tightly.
Gable ends
Use T1-11 siding sheets for the gable ends. Mark the cut lines on the sheets and then get the job done with a saw. Align the edges with attention and insert 6-8d nails, every 8″ along the framing.
Building the overhangs
Build overhangs for the shed from 2×4 lumber. You can adjust the size of overhangs to suit your needs. Drill pilot holes through the rafters and insert 2 1/2″ screws into the blocking.
Fitting the overhangs
Fit the overhangs to the front and to the back of the shed. Align the edges with attention, drill pilot holes and insert 2 1/2″ screws to lock them into place tightly.
Roof sheets
Fit 3/4″ plywood sheets to the roof of the shed. Align the sheets with attention, making sure you leave no gaps between them. Insert 1 5/8″ screws to lock the sheets into place, every 8″ along the rafters.
Front and back wall trims
Use 2×6 lumber for the front and back roof trims. Cut the trims as shown in the diagram. Attach the trims to the gable ends and then lock them into place with 2 1/2″ screws.
Side roof trims
Fit 1×6 trims to the sides of the roof. Align the edges with attention and then insert 2″ nails to lock them into place tightly.
Fitting the roofing
Cover the roofing sheets with tar paper. Install the tar paper starting with the bottom of the roof and make sure the strips overlap for at least 2″. In addition, fit a 12” strip over the top ridge. Install the shingles starting with the left- bottom of the roof, after fitting the starting course. Use roofing tacks to secure the shingles into place.
4×12 shed plans – front view
This shed is narrow and it is ideal if you need storage space but you have a narrow backyard.
4×12 shed plans – back view
Make sure you take a look over PART 1 and PART 3 of the project, so you learn how to build the frame and how to build the front door.
Thank you for reading our project about free 4×12 gable shed roof plans and I recommend you to check out the rest of the projects. Don’t forget to LIKE and SHARE our projects with your friends, by using the social media widgets. SUBSCRIBE to be the first that gets our latest projects.
EXPLORE MORE IDEAS:
 |
 |
 |
 |
 |