Duck House Roof Plans

This step by step woodworking project is about duck house roof plans free. This is PART 2 of the duck house project, where I show you how to build the roof structure and how to attach the door. This duck house has a lean to roof so it drains the water properly and a large front door you can lock to protect the ducks from predators. See my other DIY projects HERE.

We recommend you to invest in the best materials you could afford. Therefore, you should buy weather-resistant lumber, such as pine or cedar. Always take accurate measurements before adjusting the size of the components at the proper size. Drill pilot holes trough the components before inserting the wood screws, to prevent the wood from splitting. See all my Premium Plans in the Shop.

Made from this plan

Building a diy duck house

Materials

G – 4 pieces of 2×2 lumber – 60″ long, 2 pieces – 8 1/4″ long, 2 pieces – 4 1/4″ long RAFTERS
H – 1 piece of 3/4″ plywood – 35 3/4″x60″ long, 1 piece – 20 1/4″x60″ long ROOF
I – 25 sq ft of tar paper, 25 sq ft of asphalt shingles ROOFING
J – 2 pieces of 1×4 lumber – 31 1/2″ long, 1 piece – 28 3/4″ long JAMBS
K – 2 pieces of 1×4 lumber – 24 1/2″ long, 2 pieces – 21 3/4″ long, 1 piece of T1-11 siding – 21 3/4″x31 long DOOR

3 pieces of 3/4″ plywood – 4’x8
4 pieces of 2×2 lumber – 8′
2 pieces of 1×4 lumber – 8′
2 hinges, 1 latch , 1/4 hardware cloth
2 1/2″ screws, 1 1/4″ screws, 1 5/8″ screws
25 sq ft of tar paper, 25 sq ft of asphalt shingles
wood filler , wood glue, stain/paint

Tools

Safety gloves, glasses
Miter saw, jigsaw
Chalk line, tape measure, spirit level, carpentry pencil
Drill machinery and drill bits

Time

One Day

How to build a duck house roof

Building the rafters

First of all, you have to cut the rafters for the duck house. Mark the cut lines on the 2×2 pieces of lumber and then get the job done with a circular saw. Smooth the edges with sandpaper and remove the residues with a damp cloth.

Fitting the rafters

Fit the rafters to the top of the chicken coop, making sure you place them equally-spaced. Drill pilot holes through the rafters and insert 2 1/2″ screws into the plates.

Fitting the side roof supports

Attach 2×2 supports to the sides of the roof, so you can attach the chicken wire. You will use these top triangles as vents for the duck coop.

Attaching the chicken wire

Staple the chicken wire to the sides of the duck coop.

Fitting the roofing sheet

Cut the roof sheets from 3/4″ plywood after taking accurate measurements. Center the sheets to the rafters so the joint falls on the middle, as seen in the plans. Drill pilot holes through the roof sheets and insert 1 5/8″ screws to lock them into place tightly.

Fitting the roofing

Cover the roof with tar paper and then attach asphalt shingles, starting with the bottom part up to the top. In addition, you need to install drip edges so you seal the roof tightly.

Fitting the door jambs

Attach 1×4 trims around the door opening with 1 1/4″ brad nails.

Building the door

Build the door for the duck coop from 1×4 trims and T1-11 siding. You can use the piece of T1-11 siding that you have cut out in a previous step and attach 1×4 trims to reinforce it. Use 1 1/4″ brad nails and glue to assemble the door.

Fitting the door

Fit the door to the opening and lock it to the jambs with hinges. In addition, you need to add a latch so you can lock the door and protect the ducks from predators.

Building a duck house

This duck coop is really sturdy and it provides ideal conditions for the ducks to grow healthy. Of course, you can make a few adjustments or modifications to my plans so the shelter suits your needs.

Thank you for reading our project about duck house plans and I recommend you to check out the rest of the projects. Don’t forget to LIKE and SHARE our projects with your friends, by using the social media widgets. SUBSCRIBE to be the first that gets our latest projects.

<< Previous | Next >>

PRINT PLAN