Â
This step by step woodworking project is about miter saw stand plans. If you have a miter saw then you need to build a proper stand, so you can make most of it and speed up the cutting process. This miter saw stand is both sturdy, compact and has a special feature that allows you to adjust the size of the extensions, so they match the height of the miter saw’s deck. See my other DIY projects HERE.
We recommend you to invest in the best materials you could afford. Therefore, you should buy weather-resistant lumber, such as pine or cedar. Always take accurate measurements before adjusting the size of the components at the proper size. Drill pilot holes trough the components before inserting the wood screws, to prevent the wood from splitting. See all my Premium Plans in the Shop.
Â
Â
Made from this plan
Â
Â
Miter Saw Stand Plans
Â
Materials
- A – 4 pieces of 1×4 lumber – 34″ long LEGS
- B – 4 pieces of 1×4 lumber – 30 1/2″ long, 2 pieces – 16 1/2″ long FRAMES
- C – 2 pieces of 1×4 lumber – 80″ long, 5 pieces – 12″ long TABLETOP
- D – 1 piece of 3/4″ plywood – 16 1/2″x32″ long TOP
- E – 2 pieces of 1×4 lumber – 23 1/4″ long, 2 pieces – 6″ long, 1 piece of 1×6 lumber – 23 1/4″ long, 2 pieces of 1×2 lumber – 3″ long 2xEXTENSION
- 8 pieces of 1×4 lumber – 8′
- 1 piece of 1×6 lumber – 8′
- 1 piece of 3/4″ plywood – 2’x4′
- 1 1/4″ screws, 1 1/2″ brad nails
- stain, glue, putty
Tools
- Safety gloves, glasses
- Miter saw, jigsaw
- Chalk line, tape measure, spirit level, carpentry pencil
- Drill machinery and drill bits
Time
- One Day
Â
Â
Build a miter saw stand
The first step of the project is to assemble the sides for the miter saw stand. Cut the components from 1×4 lumber. Align the components with attention. Add glue to the joints and make sure the corners are square. Drill pilot holes and insert 1 1/4″ screws.
Assemble the miter saw stand by attaching the base frame. Cut the 1×4 slats at the right dimensions that are illustrated in the diagram. Drill pilot holes through the frame and insert 1 1/4″ screws into the legs.
Build the tabletop frame from 1×4 lumber. Drill pocket holes at both ends of the 12″ long and insert 1 1/4″ pocket screws. Add glue to the joints and make sure the corners are right-angled.
Attach the tabletop frame to the stand. Drill pilot holes through the tabletop frame and insert 1 1/4″ screws. Use a spirit level to make sure the tabletop is horizontal.
Build the tabletop from 3/4″ plywood. Mark the cut lines on the plywood sheet and get the job done with a saw. Attach the tabletop to the miter saw stand and align the edges with attention. Use 1 1/4″ brad nails to lock the tabletop into place. Align the edges flush.
Build the deck extensions from 1×4 lumber and from 1×6 lumber. Drill pilot holes through the 1×4 back slat and insert 1 1/4″ screws into the horizontal slat. Make sure the corners are right-angled.
Attach the 1×4 supports to the deck extensions. Drill pocket holes along the top of the supports and insert 1 1/4″ screws to assemble everything together tightly.
Fit the 1×2 pieces of lumber to the table, so you guide the deck extensions.
Fit the deck extensions into place and then adjust their height with the deck of the miter saw. Lock them into place by inserting 1 1/4″ screws into the frame.
You can easily adjust the deck extensions according to the type of miter saw you are using.
Fill the dents and the holes with wood putty and let it dry out for several hours. Smooth the surface with 120-220 grit sandpaper and apply a few coats with stain and paint.
This miter saw stand is ideal for any workshop. Even if it is not folding, the miter saw stand is compact enough so you can fit it in your garage or workshop. If you like my project, don’t forget to SHARE it on Facebook and Pinterest.
Â
Â
Thank you for reading our project about miter saw table plans and I recommend you to check out the rest of the projects. Don’t forget to LIKE and SHARE our projects with your friends, by using the social media widgets. SUBSCRIBE to be the first that gets our latest projects.
Â
EXPLORE MORE IDEAS:
Â
4 comments
Nice plans and all but I don’t see a way to download them. What good are free “plans” if you can’t download them?
Thank you for the appreciation. Fortunately, there is a simple way to download the plans so you can most of them. Read how at: http://howtospecialist.com/faq/
Finished the project. The hardest part was lining up the deck extensions but all in all pretty easy project enjoyed every minute.
Miter saw stand
That’s awesome. I would love to see and feature your project on the blog. You can send a few pics here: http://howtospecialist.com/give-back/