Home Indoor Crate Display Plans

Crate Display Plans

by Jack Sander
2 comments 374 views 4 minutes read

 

This step by step woodworking project is about crate display plans. This tiered display stand is ideal for any pantry or for garage. The three crates are roomy enough so you can store many vegetables or jars. You can build this project under 30 $, using common tools and materials you find at any home improvement store. Follow my instructions and tips, so you get the job done quickly and without no problems. See my other DIY projects HERE.

We recommend you to invest in the best materials you could afford. Therefore, you should buy weather-resistant lumber, such as pine or cedar. Always take accurate measurements before adjusting the size of the components at the proper size. Drill pilot holes trough the components before inserting the wood screws, to prevent the wood from splitting. See all my Premium Plans in the Shop.

 

 

Made from this plan

DIY-Crate-Display  Add-Image

 

Crate Display Plans

Building a crate display

Building a crate display

Materials

  • A – 2 pieces of 1×3 lumber – 40 1/2″ long, 2 pieces – 56 3/4″ long LEGS
  • B – 12 pieces of 1×3 lumber – 18″ long, 12 pieces – 10 1/2″ long CRATE
  • C – 12 pieces of 1×2 lumber – 5 1/4″ long CORNER SUPPORTS
  • D – 12 pieces of 1×3 lumber – 18″ long BOTTOM
  • E – 2 pieces of 1×2 lumber – 7 1/2″ long, 2 pieces – 18″ long, 1 piece of 1/4″ plywood – 10 1/2″x18″ long CHALKBOARD

  • 8 piece of 1×3 lumber – 10′
  • 2 pieces of 1×2 lumber – 8′
  • 1 piece of 1/4″ plywood – 2’x2′
  • 1 5/8″ screws, 1 1/4″ brad nails
  • chalkboard paint
  • stain, glue, putty

Tools

  • Safety gloves, glasses
  • Miter saw, jigsaw
  • Chalk line, tape measure, spirit level, carpentry pencil
  • Drill machinery and drill bits

Time

  • One Day

 

 

Building a crate display

Building the crates

Building the crates

The first step of the project is to assemble the crates. Therefore, use 1×3 slats for the sides and 1×2 lumber for the corner supports. The easiest way to assemble the crates is to add waterproof glue to the joints and then insert 1 1/4″ brad nails. Make sure the edges are flush before inserting the brad nails.

Attaching the bottom crate slats

Attaching the bottom crate slats

Attach the 1×3 slats to the bottom of the crates, as shown in the diagram. Use 1 1/4″ brad nails and glue to lock them into place.

Legs

Legs

Next, you need to build the legs for the display stand using 1×3 lumber. As you can see in the plans, you need to round the top edge of the back legs and to cut the top of the front legs at angle.

Assembling the crate display

Assembling the crate display

After assembling the three crates you need to assemble the display stand by attaching the legs. Use glue and 1 1/4″ brad nails to secure the legs to the three crates.

Building the chalkboard

Building the chalkboard

In order to enhance the look of the tiered display stand, you need to build a chalkboard and attach it to the top of the back legs. Use 1×2 lumber for the frame of the chalkboard and 1/4″ plywood for the chalkboard panel. Apply a few coats of chalkboard paint over the panel and then secure it to the frame with 1 1/4″ brad nails. Add glue to the joints, as well.

Fitting the chalkboard

Fitting the chalkboard

Attach the chalkboard to the back legs, as shown in the diagram. Drill pilot holes through the legs and insert 1 1/4″ screws into the frame of the chalkboard.

How to build a display crate

How to build a display crate

Fill the holes and the dents with putty and let it dry out for several hours. Smooth the surface with 120-220 grit sandpaper. Apply a few coats if paint or stain to enhance the look of the display stand. In addition, seal the finish with clear lacquer.

Display crate plans

Display crate plans

This tiered crate display stand is ideal for any pantry, as it provides many storage space for your vegetables. If you like my project, don’t forget to SHARE it on Facebook and Pinterest.

Smart Tip: Don’t forget to share your projects with me, as I love seeing what you guys are working on. Send me the pics HERE. In addition, take a look over the rest of my DIY projects HERE.

 

 

Thank you for reading our project about display crate plans and I recommend you to check out the rest of the projects. Don’t forget to LIKE and SHARE our projects with your friends, by using the social media widgets. SUBSCRIBE to be the first that gets our latest projects.

 

<b>PRINT PLAN<b> PRINT PLAN

EXPLORE MORE IDEAS:

 

You may also like

2 comments

Carlos - 7:29 pm

Sould I use nails or screws to attach the legs to the crates?
Thanks

Reply
Jack Sander - 7:30 am

Screws are the better choice.

Reply

Leave a Comment

* By using this form you agree with the storage and handling of your data by this website.