Single bed plans

This step by step diy project is about single bed frame plans. This article is about building a twin size bed frame out of 2×4 and 1×4 lumber. Follow the instructions and pay attention to the diagrams and build the wooden bed in just one weekend, even if you are a beginner when it comes to woodworking. Take a look over the rest of the project, to learn more about building furniture by yourself.

You should always plan everything from the very beginning, in order to prevent costly mistakes and to save time. Taking into account the traditional and simple design, this bed frame can match the style of any home. Mark the cut lines on the slats before making the cuts and use a saw to get the job done. If you are looking for other designs or sizes, you should check out the rest of the bed frame plans.

There are a few tips that you should take into account, if you want to get a professional result. Therefore, take accurate measurements and use professional tool when making the cuts or when drilling pilot holes. Align the components at both ends and add waterproof glue to the joints, if you want to create a rigid structure. Round the exposed edges with sandpaper or by using a good router. See all my Premium Plans in the Shop.

Made from this plan

Building a single bed

Materials

A – 2 pieces of 4×4 lumber – 25″ long, 2 pieces – 37″ long LEGS
B – 4 pieces of 1×4 lumber – 39″ long, 8 pieces of 2×4 lumber – 25″ long PANEL
C – 1 piece of 2×4 lumber – 48″ long TOP TRIMS
D – 4 pieces of 1×4 lumber – 39″ long, 8 pieces of 2×4 lumber – 19″ long PANEL
E – 2 pieces of 2×6 lumber – 60 1/2″ long SIDE PANEL
F – 2 pieces of 2×2 lumber – 75 1/2″ long, 17 pieces of 1×4 lumber – 39 3/4″ long SUPPORT SLATS

1 piece of 4×4 lumber – 12 ft
13 pieces of 1×4 lumber – 8 ft
6 pieces of 2×4 lumber – 8 ft
2 pieces of 2×6 lumber – 8 ft
mattress

Tools

Safety gloves, glasses
Miter saw, jigsaw
Chalk line, tape measure, spirit level, carpentry pencil
Drill machinery and drill bits

Tips

Use a good miter saw to make the angle cuts
Drill pilot holes before inserting the screws

Time

One Week

How to build a single bed

Building the footboard panel

The first step of the woodworking project is to build the panel for the footboard. Use 2×4 lumber for the vertical components and 1×4 lumber for the cleats. Drill pilot holes through the cleats and insert 1 1/4″ brad nails into the vertical components. Add glue to enhance the bond of the components. Fit the cleats to the opposite side of the panel.

Fitting the legs to the footboard

Next, attach the 4×4 legs to the panel, as shown in the diagram. Align the components with attention, making sure the panel is centered to the legs. Insert 1 1/4″ screws to create a rigid structure. Add glue to the joints and remove the excess with a damp cloth.

Attaching the top trim to the footboard

Continue the project by attaching the top trim to the footboard. Cut the trim out of 2×4 lumber and center it to the footboard, as shown in the diagram. Drill pilot holes through the trim and insert 2 1/2″ screws to create rigid joints. Add glue to enhance the bond of the components.

Building the headboard panel

The next step of the indoor woodworking project is to build the headboard panel. Cut the vertical components out of 2×4 lumber and the cleats out of 1×4 lumber. Use 1 1/4″ brad nails and glue to lock the components together. Align everything together and leave no gaps between the components, if you want to get a professional result.

Assembling the headboard

Drill pocket holes at both ends of the cleats and insert 1 1/4″ screws into the 4×4 legs. Make sure the corners are square and add glue to enhance the rigidity of the structure.

Attaching the top trim

Fit the 2×4 trim to the headboard. Drill pocket holes and secure the trim to the structure using 2 1/2″ screws. Add glue to the joints and remove the excess with a damp cloth.

Fitting the side rails

Build the side rails out of 2×6 lumber. Cut the components at the right size and drill pocket holes at both ends. Fit the rails to the headboard and footboard, making sure you insert 2 1/2″ screws to create a rigid structure. Offset the rails about 1/4″ from the interior of the bed frame.

Fitting the cleats

Continue the project by fitting the 2×2 cleats to the rails, as described in the diagram. Drill pilot holes and insert 2 1/2″ screws to secure the cleats into place properly.

Fitting the support slats

Attach 1×4 slats to the cleats, making sure you place them equally-spaced. Drill pilot holes and insert 1 1/4″ screws to secure the slats into place.

Single bed plans

Last but not least, we recommend you to take care of the finishing touches. In order to get a professional result, fill the holes and the gaps with wood filler and let it dry out for a few hours. Check if there are protruding screws and fix this issue, if necessary.

Thank you for reading our project about single bed plans and we recommend you to check out the rest of the projects. Don’t forget to SHARE and LIKE our projects with your friends, by using the social media widgets, if you want to help us keep adding free woodworking plans.

PRINT PLAN