This step by step woodworking project is about 8×10 gambrel shed roof plans. This is the PART 2 of the 8×10 garden shed project, where I show you how to build the gambrel roof for the shed. Building the roof for the shed is really easy if you follow my tips and diagrams with attention. Read the local codes before starting the project, so you comply with the requirements. See my other DIY projects HERE.
We recommend you to invest in the best materials you could afford. Therefore, you should buy weather-resistant lumber, such as pine or cedar. Always take accurate measurements before adjusting the size of the components at the proper size. Drill pilot holes trough the components before inserting the wood screws, to prevent the wood from splitting.
Made from this plan
8×10 Gambrel Shed Roof – Free DIY Plans
- E – 2 pieces of 2×4 lumber – 98 1/2″ long, 2 pieces – 48″ long, 1 piece – 34 3/4″ long, 2 pieces – 36 3/4″ long, 1 piece – 45 3/4″ long FRONT WALL
- G – 4 pieces of T1-11 siding – 48″x66″ long, 2 pieces – 24″x66″ long, 4 pieces – 48″x115 3/4″ long SIDING
- H – 4 pieces of 2×4 lumber – 38″ long 9xTRUSS
- I – 4 pieces of 3/4″ plywood – 38″x96″ long, 4 pieces – 38″x24″ long ROOF
- J – 8 pieces of 1×6 lumber – 38 1/2″ long TRIMS
- K – 150 sq ft of tar paper, 150 sq ft of asphalt shingles ROOFING
- 4 pieces of T1-11 siding – 4’x10′
- 7 pieces of T1-11 siding – 4’x8′
- 24 pieces of 2×4 lumber – 8′
- 2 pieces of 2×4 lumber – 10′
- 1 piece of 1/2″ plywood – 4’x8′
- 5 pieces of 3/4″ plywood – 4’x8′
- 4 pieces of 1×6 lumber – 8′
- 150 sq ft of tar paper, 150 sq ft of asphalt shingles
- 2 1/2″ screws, 3 1/2″ screws, 1 5/8″ screws
- 4d nails, 6d nails
- rafter ties
- wood filler , wood glue, stain/paint
- Safety gloves, glasses
- Miter saw, jigsaw
- Chalk line, tape measure, spirit level, carpentry pencil
- Drill machinery and drill bits
- One week
8×10 Gambrel Shed Roof – DIY Plans
Use 2×4 lumber for the rafters. Mark the cut lines on the beams and then get the job done with a circular saw. Smooth the edges with sandpaper.
Use 1/2″ plywood for the gussets. Use a circular saw to make the cuts, as shown in the diagram. Add the gussets to the rafters and lock them into place with 1 5/8″ screws.
Fit the rafters to the top of the shed. Place the rafters every 16″ on center, equally spaced, as shown in the diagram. Drill pilot holes and insert 3 1/2″ screws to lock the rafters into place tightly. Alternatively, you can use rafter ties to lock the trusses to the plates.
Use 2×4 lumber for the front wall frame. Use a miter saw to make the angle cuts and then secure them into place tightly. Take accurate measurements and drill pilot holes before inserting the screws, to prevent the wood from splitting.
Use 2×4 lumber for the gambrel end supports. Drill pocket holes at both ends of the supports and then insert 2 1/2″ screws to lock them into place tightly.
Use T1-11 siding sheets for the side wall panels. Mark the cut lines on the sheets and then get the job done with a saw. Align the edges with attention and insert 6-8d nails, every 8″ along the framing.
Fit the panels to the front and back walls. As you can see in the diagram, you need to make a few cuts to fit the front panels around the door opening.
Fit 3/4″ plywood sheets to the roof of the shed. Align the sheets with attention, making sure you leave no gaps between them. Insert 1 5/8″ screws to lock the sheets into place, every 8″ along the rafters.
Use 1×6 lumber for the front and back roof trims. Cut the trims as shown in the diagram. Attach the trims to the gable ends and then lock them into place with 2 1/2″ screws.
Cover the roofing sheets with tar paper. Install the tar paper starting with the bottom of the roof and make sure the strips overlap for at least 2″. In addition, fit a 12” strip over the top ridge. Install the shingles starting with the left- bottom of the roof, after fitting the starting course. Use roofing tacks to secure the shingles into place.
This shed is ideal if you need storage space but you have a narrow backyard. Make sure you take a look over PART 1 and PART 3 of the project, so you learn how to build the frame and how to build the front door.
Thank you for reading our project about free 8×10 gambrel shed roof plans and I recommend you to check out the rest of the projects. Don’t forget to LIKE and SHARE our projects with your friends, by using the social media widgets. SUBSCRIBE to be the first that gets our latest projects.