12×10 Shed Roof Plans

This step by step woodworking project is about 12×10 gable shed roof plans plans. This is the PART 2 of the 12×10 garden shed project, where I show you how to build the gable roof for the shed. The gable roof has a 30 degree slope and it will add unique charm to the shed. My plans come with step by step instructions and you can easily adjust all the dimensions to suit your needs. See my other DIY projects HERE.

We recommend you to invest in the best materials you could afford. Therefore, you should buy weather-resistant lumber, such as pine or cedar. Always take accurate measurements before adjusting the size of the components at the proper size. Drill pilot holes trough the components before inserting the wood screws, to prevent the wood from splitting. See all my Premium Plans HERE.

 

 

Made from this plan

Add-Image

 

 

12×10 Shed Plans

Building a 12x10 shed

Building a 12×10 shed

 

Materials

  • G – 4 pieces of T1-11 siding – 48″x31 3/4″ long, 2 pieces – 24″x45 1/2″ long SIDING
  • H – 2 pieces of 2×4 lumber – 96″ long, 1 piece – 144″ long 6xTRUSS
  • H – 2 pieces of 2×4 lumber – 25 1/4″ long, 1 piece – 38″ long 6xSUPPORTS
  • I – 4 pieces of 2×4 lumber – 25 1/4″ long, 2 pieces – 38″ long SUPPORTS
  • I – 4 pieces of 3/4″ plywood – 4’x8′ long, 4 pieces – 2’x4′ ROOF
  • J – 4 pieces of 2×6 lumber – 97 1/4″ long, 2 pieces of 1×6 lumber – 121 1/4″ long TRIMS
  • K – 200 sq ft of tar paper, 200 sq ft of asphalt shingles ROOFING

Tools

Time

  • One week

 

 

Building a 12×10 gable shed

Building the trusses

Building the trusses

First of all, you need to build the trusses for the 12×10 gable shed. Cut the bottom rafter and the regular rafters from 2×4 lumber. Use a miter saw for accurate repetitive cuts. Set the miter at 30 degrees for the rafters. Set the miter at 60 degrees for the bottom chord. Lay the rafters on a level surface and leave no gaps between the components.

Fitting the truss supports

Fitting the truss supports

Use 2×4 lumber for the supports. Leave no gaps between then components and then reinforce the joints with metal plates or with 1/2″ plywood gussets. Make 30 degree cuts to the supports.

Fitting the trusses

Fitting the trusses

Fit the trusses to the top of the shed, every 24″ on center. Plumb the trusses and then lock them into place with rafter ties.

Gable end panels

Gable end panels

Fit the T1-11 siding sheets to the gable ends of the shed. Mark the cut lines on the sheets and then get the job done with a saw. Smooth the edges with sandpaper and then attach them into place tightly. Insert 6-8d nails every 8″ along the framing.

Fitting the roof sheets

Fitting the roof sheets

Fit the 3/4″ plywood sheets to the roof of the shed, as shown in the diagram. Align the edges flush and leave no gaps between them. Use 1 5/8″ screws to lock the sheets into place tightly, every 8″ along the framing.

Side roof trims

Side roof trims

Fit 1×6 trims to the sides of the shed. Align the edges and insert 2″ nails to lock them into place tightly.

Front and back roof trims

Front and back roof trims

Fit the 2×6 trims to the front and back of the shed with 2 1/2″ screws. You can also make overhangs, if you want.

Fitting the roofing

Fitting the roofing

The next step of the woodworking project is to cover the roof with felt. As you can see in the image, you need to make sure the strips of roofing felt overlap at least 2”. In addition, you have to lock the tar paper to the plywood sheets with staples. Make sure you cover the top ridge with a 12” strip of roofing felt. The front and back drip edges should be fitted under the felt, while the sides over.

Next, you should install the shingles to the roof of the large shed. Start with the bottom of the roof, by fitting the first course, as in the image. Use roofing tacks to secure the shingles to the roofing sheets.

Start the first course with a full tab, the second with 2 1/2 tabs, the third with 2 tabs, the forth with 1 1/2 tabs, the fifth with 1 tab, the sixth with half tab and the seventh with a 3 tabs. Secure the shingles with roofing tacks.

12x10 Shed Plans - front view

12×10 Shed Plans – front view

This shed project is super easy to complete from the ground up to the roof, using my free plans. This shed is ideal for any backyard, as you can use it both for storage and as a workshop. You can repair your tools, bikes and so much more in this beautiful and functional shed.

Smart Tip: Don’t forget to share your projects with me, as I love seeing what you guys are working on. Send me the pics HERE. In addition, take a look over the rest of my DIY projects HERE.

 

 

Thank you for reading our project about free 12×10 gable shed roof plans and I recommend you to check out the rest of the projects. Don’t forget to LIKE and SHARE our projects with your friends, by using the social media widgets. SUBSCRIBE to be the first that gets our latest projects.

 

<< Previous  |  Next >>

 




Related Posts

Add Comment