Swing Stand Plans

This step by step diy project is about how to build a swing stand plans. This garden project features detailed instructions regarding the construction of a basic swing stand. Don’t forget to take a look over this article and this article, in order to see how to build the swing bench. This stand has the great advantage that you don’t need to set the posts into concrete.

You should always plan everything from the very beginning, in order to prevent costly mistakes and to save time. In most of the cases, you need a friend to give you a hand when assembling the wooden swing stand. Invest in high quality lumber and plywood, as the components will be exposed to bad weather. Protect the components with appropriate paint or stain.

There are a few tips that you should take into account, if you want to get a professional result. Therefore, take accurate measurements and use professional tools when making the cuts or when drilling pilot holes. Align the components at both ends and add waterproof glue to the joints, if you want to create a rigid structure. PDF downloadable plans with premium features in the Store.

 

Made from this plan

DIY-Swing-StandDIY-Swing-Stand-with-Bench DIY-Swing-StandDIY-Porch-Swing-with-Stand Add-Image

 

Swing stand plans

Building a swing stand

Building a swing stand

 

Materials

  • A – 2 pieces of 4×4 lumber – 87 1/2″ long POSTS
  • B – 4 pieces of 2×6 lumber – 48″ long, 4 pieces of 4×4 lumber – 22 3/4″ long BASE
  • C – 2 pieces of 4×4 lumber – 25 1/2″ long, 2 pieces – 12″ lumber BRACES
  • C – 2 pieces of 2×8 lumber – 120″ long SUPPORT BEAMS
  • D – 8 pieces of 4×4 lumber – 22 1/2″ long RAFTERS

Tools

Tips

  • Use a good miter saw to make the angle cuts
  • Drill pilot holes before inserting the screws

Time

  • One Week

Related

 

 

How to build  a swing stand

Fitting the posts

Fitting the posts

 

Use 4×4 lumber to build the posts for the swing stand. If you want to set the posts into concrete, you need to dig 3′ deep holes and use anchors. Use temporarily braces to lock them into place till the concrete dries out. Use a spirit level to make sure the posts are plumb.

 

Fitting the base supports

Fitting the base supports

 

Build the base of the stand out of 2×6 beams. Cut both ends of the beams in a decorative manner. Drill pilot holes through the beams and through the posts. Insert 7″ carriage bolts and lock everything together tightly. Leave no gaps between the components and make sure everything is locked together tightly.

 

Fitting the base braces

Fitting the base braces

 

Build the braces for the stand out of 4×4 lumber. Cut both ends of the braces at 45 degrees and lock them to the base with 3 1/2″ screws. Leave no gaps between the components and make sure the corners are square.

 

Building the support beams

Building the support beams

 

Build the support beams out of 2×8 lumber. Cut both ends in a decorative manner and smooth the edges with fine-grit sandpaper.

 

Fitting the support beams

Fitting the support beams

 

Clamp the support beams to the top of the posts and use a spirit level to check if they are horizontal. Drill pilot holes through the beams and through the posts and lock them together tightly with 7″ carriage bolts.

 

Fitting the braces

Fitting the braces

 

In order to add support to the structure, we recommend you to install 4×4 braces to the swing stand. Cut both ends of the braces at 45 degrees and lock them to the structure using 2 1/2″ screws.

 

Fitting the swing bench supports

Fitting the swing bench supports

 

In order to hang the swing bench, you have to attach 4×4 supports between the beams. As you can easily notice in the diagram, cut one end of the supports at 45 degrees. Secure the supports into place by inserting 2 1/2″ screws or 7″ carriage bolts.

 

Building the rafters

Building the rafters

 

Build the rafters out of 4×4 lumber. Cut the both ends of the rafters as shown in the diagram and make notches by using a circular saw. Smooth the recess with a sandpaper and remove the residues with sandpaper.

 

Attaching the rafters

Attaching the rafters

 

Fit the rafters to the support beams, as described in the diagram. Place the rafters equally-spaced, as shown in the plans. Drill pilot holes through the rafters and insert 3 1/2″ screws into the support beams. Leave no gaps between the components for a professional result.

 

Swing stand plans

Swing stand plans

 

Last but not least, we recommend you to take care of the finishing touches. In order to get a professional result, fill the holes and the gaps with wood filler and let it dry out for a few hours. Check if there are protruding screws and fix this issue, if necessary.

Smart Tip: Apply a few coats of stain or exterior paint to the components, in order to protect them from decay and water damage. Check out the rest of the outdoor plans featured on our website. PDF downloadable plans with premium features in the Store.

 

 

Thank you for reading our project about swing stand plans and we recommend you to check out the rest of the projects. Don’t forget to SHARE and LIKE my projects with your friends, by using the social media widgets, if you want to help us keep adding free woodworking plans.




Related Posts

13 Comments

  1. Jim
    • Jack Sander
  2. mojo
    • Jack Sander
    • Jack Sander
    • Jack Sander
  3. Stephen Hendricks
  4. Stephen Hendricks
  5. Frank Gingras
    • Jack Sander
    • Frank Gingras
  6. Madelyn Bourassa

Add Comment

Leave a Reply to mojo Cancel reply